OT: Help at InfoAge 7/31 for drilling holes, cutting blocking, mounting equipment
Martin will be at InfoAge on July 31 from 9AM to 5PM and needs help with the following: - Set the cable anchors in the hotel basement for the fiber optic cables (about a dozen 1/4" holes in the concrete beam between the front wall of the hotel and the column by the rack) - Open up the holes for the equipment rack in the hotel basement floor. (four 1/2" holes with a hammer drill) - Mount the network equipment rack in the furnace room at the read of 9032A. - Assemble and rack the second UPS in 9059, and move red power cables to it. - Drill the hole from the media recover office on the second floor of the hotel into the attic. (one 1/2" hole with a hammer drill) - Cut the blocking for the underside of the engineers desk in 9059 with the little table saw. Anyone willing to help anywhere in that time frame? ========================================= Jeff Brace Vice President & Board Member Vintage Computer Festival East Show-runner Vintage Computer Federation is a 501c3 charity http://www.vcfed.org/ jeffrey@vcfed.org
Not sure what your equipment is like, but I've got a Hilti SDS rotary hammer if you guys have only a standard hammer drill. That concrete is going to be old and very tough! Thanks, Jonathan ‐‐‐‐‐‐‐ Original Message ‐‐‐‐‐‐‐ On Sunday, July 25th, 2021 at 16:09, Jeffrey Brace via vcf-midatlantic <vcf-midatlantic@lists.vcfed.org> wrote:
Martin will be at InfoAge on July 31 from 9AM to 5PM and needs help with
the following:
- Set the cable anchors in the hotel basement for the fiber optic cables
(about a dozen 1/4" holes in the concrete beam between the front wall of
the hotel and the column by the rack) - Open up the holes for the equipment rack in the hotel basement floor.
(four 1/2" holes with a hammer drill) - Mount the network equipment rack in the furnace room at the read of
9032A. - Assemble and rack the second UPS in 9059, and move red power cables to
it. - Drill the hole from the media recover office on the second floor of
the hotel into the attic. (one 1/2" hole with a hammer drill) - Cut the blocking for the underside of the engineers desk in 9059 with
the little table saw.
Anyone willing to help anywhere in that time frame?
=========================================
Jeff Brace
Vice President & Board Member
Vintage Computer Festival East Show-runner
Vintage Computer Federation is a 501c3 charity
jeffrey@vcfed.org
Bring your implements of destruction!! Likely better than our hammer drill. Got a 1/4" bit for it?? Martin On 7/25/2021 4:31 PM, Jonathan Chapman via vcf-midatlantic wrote:
Not sure what your equipment is like, but I've got a Hilti SDS rotary hammer if you guys have only a standard hammer drill. That concrete is going to be old and very tough!
Thanks, Jonathan
‐‐‐‐‐‐‐ Original Message ‐‐‐‐‐‐‐
On Sunday, July 25th, 2021 at 16:09, Jeffrey Brace via vcf-midatlantic <vcf-midatlantic@lists.vcfed.org> wrote:
Martin will be at InfoAge on July 31 from 9AM to 5PM and needs help with
the following:
- Set the cable anchors in the hotel basement for the fiber optic cables
(about a dozen 1/4" holes in the concrete beam between the front wall of
the hotel and the column by the rack) - Open up the holes for the equipment rack in the hotel basement floor.
(four 1/2" holes with a hammer drill) - Mount the network equipment rack in the furnace room at the read of
9032A. - Assemble and rack the second UPS in 9059, and move red power cables to
it. - Drill the hole from the media recover office on the second floor of
the hotel into the attic. (one 1/2" hole with a hammer drill) - Cut the blocking for the underside of the engineers desk in 9059 with
the little table saw.
Anyone willing to help anywhere in that time frame?
=========================================
Jeff Brace
Vice President & Board Member
Vintage Computer Festival East Show-runner
Vintage Computer Federation is a 501c3 charity
jeffrey@vcfed.org
SDS bits from small Tapcon to 1" I believe! I'll see if I can either make it up or send it with someone. Thanks, Jonathan ‐‐‐‐‐‐‐ Original Message ‐‐‐‐‐‐‐ On Sunday, July 25th, 2021 at 16:44, Martin Flynn via vcf-midatlantic <vcf-midatlantic@lists.vcfed.org> wrote:
Bring your implements of destruction!!
Likely better than our hammer drill.
Got a 1/4" bit for it??
Martin
On 7/25/2021 4:31 PM, Jonathan Chapman via vcf-midatlantic wrote:
Not sure what your equipment is like, but I've got a Hilti SDS rotary hammer if you guys have only a standard hammer drill. That concrete is going to be old and very tough!
Thanks,
Jonathan
‐‐‐‐‐‐‐ Original Message ‐‐‐‐‐‐‐
On Sunday, July 25th, 2021 at 16:09, Jeffrey Brace via vcf-midatlantic vcf-midatlantic@lists.vcfed.org wrote:
Martin will be at InfoAge on July 31 from 9AM to 5PM and needs help with
the following:
- Set the cable anchors in the hotel basement for the fiber optic cables
(about a dozen 1/4" holes in the concrete beam between the front wall of
the hotel and the column by the rack)
- Open up the holes for the equipment rack in the hotel basement floor.
(four 1/2" holes with a hammer drill)
- Mount the network equipment rack in the furnace room at the read of
9032A.
- Assemble and rack the second UPS in 9059, and move red power cables to
it.
- Drill the hole from the media recover office on the second floor of
the hotel into the attic. (one 1/2" hole with a hammer drill)
- Cut the blocking for the underside of the engineers desk in 9059 with
the little table saw.
Anyone willing to help anywhere in that time frame?
=========================================
Jeff Brace
Vice President & Board Member
Vintage Computer Festival East Show-runner
Vintage Computer Federation is a 501c3 charity
jeffrey@vcfed.org
I can come down as well. I'll bring my Bosch SDS-Plus hammer drill but I only have 1/2" and 3/4" bits for it. The 3/4" bit says it's for concrete with rebar. -ken On Sun, Jul 25, 2021 at 4:44 PM Martin Flynn via vcf-midatlantic < vcf-midatlantic@lists.vcfed.org> wrote:
Bring your implements of destruction!!
Likely better than our hammer drill.
Got a 1/4" bit for it??
Martin
On 7/25/2021 4:31 PM, Jonathan Chapman via vcf-midatlantic wrote:
Not sure what your equipment is like, but I've got a Hilti SDS rotary hammer if you guys have only a standard hammer drill. That concrete is going to be old and very tough!
Thanks, Jonathan
‐‐‐‐‐‐‐ Original Message ‐‐‐‐‐‐‐
On Sunday, July 25th, 2021 at 16:09, Jeffrey Brace via vcf-midatlantic < vcf-midatlantic@lists.vcfed.org> wrote:
Martin will be at InfoAge on July 31 from 9AM to 5PM and needs help with
the following:
- Set the cable anchors in the hotel basement for the fiber optic cables
(about a dozen 1/4" holes in the concrete beam between the front wall of
the hotel and the column by the rack) - Open up the holes for the equipment rack in the hotel basement floor.
(four 1/2" holes with a hammer drill) - Mount the network equipment rack in the furnace room at the read of
9032A. - Assemble and rack the second UPS in 9059, and move red power cables to
it. - Drill the hole from the media recover office on the second floor of
the hotel into the attic. (one 1/2" hole with a hammer drill) - Cut the blocking for the underside of the engineers desk in 9059 with
the little table saw.
Anyone willing to help anywhere in that time frame?
=========================================
Jeff Brace
Vice President & Board Member
Vintage Computer Festival East Show-runner
Vintage Computer Federation is a 501c3 charity
jeffrey@vcfed.org
I have a pack of decent SDS bits that I bought by accident a while ago (I don't have an SDS hammer, but hope to some day). I think there's probably a 1/4" in there; I can check, and if anyone is going up near (or passing near) Arnold, MD, I'll be glad to send them on. Can't make it up myself right now, I'm afraid. - Dave
On Jul 26, 2021, at 12:40 PM, Kenneth Gober via vcf-midatlantic <vcf-midatlantic@lists.vcfed.org> wrote:
I can come down as well. I'll bring my Bosch SDS-Plus hammer drill but I only have 1/2" and 3/4" bits for it. The 3/4" bit says it's for concrete with rebar.
-ken
On Sun, Jul 25, 2021 at 4:44 PM Martin Flynn via vcf-midatlantic < vcf-midatlantic@lists.vcfed.org> wrote:
Bring your implements of destruction!!
Likely better than our hammer drill.
Got a 1/4" bit for it??
Martin
On 7/25/2021 4:31 PM, Jonathan Chapman via vcf-midatlantic wrote:
Not sure what your equipment is like, but I've got a Hilti SDS rotary hammer if you guys have only a standard hammer drill. That concrete is going to be old and very tough!
Thanks, Jonathan
‐‐‐‐‐‐‐ Original Message ‐‐‐‐‐‐‐
On Sunday, July 25th, 2021 at 16:09, Jeffrey Brace via vcf-midatlantic < vcf-midatlantic@lists.vcfed.org> wrote:
Martin will be at InfoAge on July 31 from 9AM to 5PM and needs help with
the following:
- Set the cable anchors in the hotel basement for the fiber optic cables
(about a dozen 1/4" holes in the concrete beam between the front wall of
the hotel and the column by the rack) - Open up the holes for the equipment rack in the hotel basement floor.
(four 1/2" holes with a hammer drill) - Mount the network equipment rack in the furnace room at the read of
9032A. - Assemble and rack the second UPS in 9059, and move red power cables to
it. - Drill the hole from the media recover office on the second floor of
the hotel into the attic. (one 1/2" hole with a hammer drill) - Cut the blocking for the underside of the engineers desk in 9059 with
the little table saw.
Anyone willing to help anywhere in that time frame?
=========================================
Jeff Brace
Vice President & Board Member
Vintage Computer Festival East Show-runner
Vintage Computer Federation is a 501c3 charity
jeffrey@vcfed.org
participants (5)
-
David Riley -
Jeffrey Brace -
Jonathan Chapman -
Kenneth Gober -
Martin Flynn