May 2021 - vcf-midatlantic - lists.vcfed.org

Re: [vcf-midatlantic] (no subject)
by Bob Aviles 12 May '21

12 May '21

My version is for the Sun systems, one drive is Iomega Bernoulli removable. Bobby On Tuesday, May 11, 2021, 07:46:50 PM EDT, Peter Cetinski via vcf-midatlantic <vcf-midatlantic(a)lists.vcfed.org> wrote: > On May 11, 2021, at 6:45 PM, Bill Degnan via vcf-midatlantic <vcf-midatlantic(a)lists.vcfed.org> wrote: > > This came in through the kennettclassic.com contact form: > > "we need working 10 meg cartridge system > can you help?" > > What do you think this person is referring to? > > Bill Iomega Bernoulli 10MB removable cartridge drive

1 0

SEMI-OT: Samsung laptops
by Stephen A Edwards 12 May '21

12 May '21

Some colleagues of mine are looking for some very specific laptop models, in the 10-15 year-old range. If you or anybody you know has a line on any of these, please contact me off-list. There's some reasonable money involved, but the model numbers must be an exact match. Here's their wishlist: Samsung RF510-S01 Samsung RF510-S02 Samsung RF511-S02 Samsung RF511-S03 Samsung RF710-S02 Samsung RF711-S01 Samsung RF711-S02 Dell Latitude D410 (Samsung NP400B2B-A01)

4 4

10 meg cartridge system
by Bill Degnan 11 May '21

11 May '21

This came in through the kennettclassic.com contact form: "we need working 10 meg cartridge system can you help?" What do you think this person is referring to? Tallgrass? Corvus? Alloy? Bill

3 4

(no subject)
by Bill Degnan 11 May '21

11 May '21

This came in through the kennettclassic.com contact form: "we need working 10 meg cartridge system can you help?" What do you think this person is referring to? Bill

5 4

Re: [vcf-midatlantic] (no subject)
by W. Bryan Caudle 11 May '21

11 May '21

Something like this? We have one of these drives but it is untested at this time. Would be happy to loan it out or collaborate on a project if needed. Sent from my iPhone > On May 11, 2021, at 6:53 PM, Bob Aviles via vcf-midatlantic <vcf-midatlantic(a)lists.vcfed.org> wrote: > > > <mime-attachment>

1 1

Value of Air Compressor in CDL workshop
by Martin Flynn 11 May '21

11 May '21

CDL has an offer on the table for the donation of a used 5HP air compressor. Grainger Model is 3Z724, needs work. Any value during workshops other than air for soldering stations?

11 16

Mac IIci, dead after power on
by Ethan O'Toole 10 May '21

10 May '21

Working on IIci I picked up at swap meet. Ex-Cisco, it's gonna be sweet. I read that the battery doesn't matter. Pulled it. Zero leakage. Pre-recap, no life. Post-recap, no life. (Re-capped machine.) 5v 500ma line is fine from the PSU 12v line is fine from the PSU 5v line is fine from the PSU Not sure about -12, but probably just audio? No power on chime. Screen is black, monitor wakes up. Haven't used the DB-15 to VGA 6 switch converter in ages but it worked last time. Powers on from keyboard or rear panel switch. I guess the first things to check are the CPU reset circuit and the clock. Any other pointers from Mac geeks? :-) Recapped the A1200 motherboard I picked up and it booted! Now trying to decide on keyboard options. - Ethan

5 7

The KENBAK is Back (Again)
by Chris Fala 10 May '21

10 May '21

I know there are already replicas of this computer, but it is nice to see renewed interest. https://www.instructables.com/25-Scale-KENBAK-1-Personal-Computer-Reproduct…

3 2

H89 for museum; gotek?
by Herb Johnson 09 May '21

09 May '21

Just as a matter of courtesy: consider starting a new thread when the conversation changes greatly from the "subject" line. I am a user, I'm not in charge. But since I'm posting a response, I'll change the subject line. The subject of the thread "Needed SD card solutions for museum" was about SDcard adapters to replace floppy drives on 8-bit computers. But most of the thread now is entirely about an H89 acquired which may be donated to the VCFed museum; and/or about the utility of a "Gotek" hardware product for it that emulates various vintage floppy drives with file-storage. I would have ignored the thread, except by luck. I read this list online, after the fact; not by emails. And anyone looking backwards or search, would not find those H89 interests among the subject lines, until now. The H89 by Heath and Zenith is a great 8-bit Z80 system. It works fine with original hardware and software, and hard or soft sectored disks. One needs a controller for each, with drives dedicated for each. That's how it was done in the era. But people today do like putting modern widgets and new boards on it, some use modern mass storage. The H89 and support for it, or a system to restore or to pass to the Museum, are certainly worth their own discussion threads. As for modern SDcard or CompactFlash devices that emulate floppy drives, like GoTek. I don't follow them much. But it's unusual for them to support formats like Heath's hard-sectored USART based floppy controller. It's a technical challenge, not just "bugs" to fix. If GoTek supports that better over time, that's interesting and good news. Regards, Herb Johnson retrotechnology.com https://retrotechnology.com/herbs_stuff/s_zenith.html#h89 -- Herbert R. Johnson, New Jersey in the USA http://www.retrotechnology.com OR .net preserve, recover, restore 1970's computing email: hjohnson AT retrotechnology DOT com or try later herbjohnson AT comcast DOT net

5 4

vcf-midatlantic] Value of Air Compressor in CDL workshop
by Herb Johnson 09 May '21

09 May '21

> used 5HP air compressor, Grainger Model is 3Z724, needs work. > This unit is actually 208, 3 Phase. It's belt driven and only > turns 1800 RPM at the motor pulley. Just my opinions, following. This is tremendous overkill for blowing some dust off some electronics, that being any vintage-computing interest. Especially when considering it will be operated in another room, meaning running air lines to workbenches. Cans of compressed air (or a shop-vac) solve the dust-cleaning problem immediately, cleanly, no oil. Otherwise it seems to me, CDL is talking about labor and capital improvements - like running lines between rooms, housing noisy compressors, equipment maintenance, filters, etc. But CDL didn't ask for advice. They asked VCFed, what as customers of CDL what they might use at their bench. So I'll hold my tongue about advice to CDL. But if they decide against acquiring it: 1) this might be a capital equipment tool, better suited for working on cars, trucks, mowers, big mechanical stuff. Are there not other groups at InfoAge who do that stuff? Equipment Maintenance? or the military vehicle folks? they may find better use, make repairs, make/keep it portable. Then it would be available to CDL intermittently. 2) If the unit is really worn out or busted; there's that 1800RPM 5HP electric motor. That's pretty hefty, and a low rotation rate (most motors are 3600RPM). That sure would nicely feed some rotating equipment (I own a lathe myself). Or maybe a DC or AC generator, as a motor/generator set. and CDL is in the end a "maker" group, parts is part of making (seems to me). But if they don't want a motor like that, some other group at InfoAge might. regards, Herb Johnson -- Herbert R. Johnson, New Jersey in the USA http://www.retrotechnology.com OR .net preserve, recover, restore 1970's computing email: hjohnson AT retrotechnology DOT com or try later herbjohnson AT comcast DOT net

1 0