- vcf-midatlantic - lists.vcfed.org

Breakfast tomorrow for repair workshop
by Jeffrey Brace 12 Feb '23

12 Feb '23

9AM Breakfast at Princess Maria Diner -- ========================================= Jeff Brace VCF National Board Member Chairman & Vice President Vintage Computer Festival East Showrunner Vintage Computer Federation is a 501c3 charity https://vcfed.org/ <http://www.vcfed.org/> jeffrey(a)vcfed.org

1 1

TRS-80 Model 4P - Did I Leave it at the Workshop?
by Alexander Jacocks 11 Feb '23

11 Feb '23

All, I can’t figure out what I did with my Model 4P after the last workshop. Did anyone see it? It seems an odd thing to have misplaced. Thanks! - Alex

2 1

OT - air lines in the makerspace
by Martin Flynn 11 Feb '23

11 Feb '23

Was discussion quite a while back about installing the air compressor in the furnace room (for noise control) and running an air line through the attic with drops / legs in the makerspace where required With the deployment of the de-soldering and rework stations (which run on external compressed air) we will need to revisit this, and decide on where the connections will need to be, and if any drops will be deployed in the classroom area for use during VCF workshops. Direct replies on location recommendations preferred to keep the noise level down. Martin Flynn

1 0

OT - air lines in the makerspace
by Martin Flynn 11 Feb '23

11 Feb '23

Blind cross-post to vcf and cdl lists: Was discussion quite a while back about installing the air compressor in the furnace room (for noise control) and running an air line through the attic with drops / legs in the makerspace where required With the deployment of the de-soldering and rework stations (which run on external compressed air) we will need to revisit this, and decide on where the connections will need to be, and if any drops will be deployed in the classroom area for use during VCF workshops. Direct replies on location recommendations preferred to keep the noise level down. Martin Flynn

1 0

OT - Please reply directly
by Martin Flynn 10 Feb '23

10 Feb '23

Cross posted to VCF and CDL: CDL has an opportunity to acquire an HP HP8924C RF test set for the radio bench We have compatible serial and GPIB interfaces from the previously acquired HP logic analyzer. Please reply off list yes or no to proceed Martin A Flynn / W2RWJ Computer Deconstruction Laboratory 2201 Marconi Road Wall Township, NJ 07719 Tel: +01 732-456-5001 Email: martin.flynn(a)compdecon.org Online: www.compdecon.org Facebook: https://www.facebook.com/compdecon/

4 5

Dinner reservations for tomorrow (Repair Workshop)
by Jeffrey Brace 10 Feb '23

10 Feb '23

This message is for those going out to dinner to Patrick's Grill tomorrow at the repair workshop I only have 9 people signed up so far. I made the reservations just now. It was a choice between 6PM and 8PM so I chose 8PM. Please let me know if there are any questions or problems. If you want to go and are not on the dinner signup list. <https://docs.google.com/spreadsheets/d/1uPXhGjZlyJJ7xuD7sBoplteTDLXAa34svEz…>, then let me know quickly tonight and I will add to the reservation. Don't know if I can add any more tomorrow. ========================================= Jeff Brace VCF National Board Member Chairman & Vice President Vintage Computer Festival East Showrunner Vintage Computer Federation is a 501c3 charity https://vcfed.org/ <http://www.vcfed.org/> jeffrey(a)vcfed.org

1 0

Re: [vcf-midatlantic] 2/11-2/12 Repair Workshop Weekend -- I could use help with some SCSI disk data recovery
by Dan FitzGerald 10 Feb '23

10 Feb '23

Jonathan, I tried using ddrescue last night, and was able to get a disk image. But both Linux and System 7.5.5 (under Basilisk II) say that they can't find a filesystem on the image. I know that the drive is marginal, however I can actually boot the SE from it, so I am confused as to why Basilisk II and Linux are saying that there is no readable filesystem on it. Regards, Dan FitzGerald They/Them/Theirs http://www.vm.ibm.com/devpages/dfitzger -----Original Message----- From: Jonathan Sturges via vcf-midatlantic <vcf-midatlantic(a)lists.vcfed.org> Reply-To: vcf-midatlantic <vcf-midatlantic(a)lists.vcfed.org> To: vcf-midatlantic(a)lists.vcfed.org <vcf-midatlantic(a)lists.vcfed.org> Cc: Jonathan Sturges <jonathansturges(a)yahoo.com> Subject: Re: [vcf-midatlantic] 2/11-2/12 Repair Workshop Weekend -- I could use help with some SCSI disk data recovery Date: 02/10/2023 12:36:08 PM

1 0

Re: [vcf-midatlantic] 2/11-2/12 Repair Workshop Weekend -- I could use help with some SCSI disk data recovery
by Jonathan Sturges 10 Feb '23

10 Feb '23

> I will be coming to the Repair Workshop both days this weekend, and I > am bringing some Macintosh SCSI hard drives that need data recovery. > ?Are any of the folks who are coming able to bring their tools/knowhow > for imaging misbehaving SCSI disks? If the disks still spin, ddrescue is as good as anything for imaging marginal drives. If you also want to do data recovery from the saved images, I've personally had better luck with COTS tools than open source. I can recommend Disk Drill PRO. -Jonathan

1 0

Dinner on Saturday at the Repair Workshop this weekend.
by Jeffrey Brace 10 Feb '23

10 Feb '23

If you didn't already let me know, then let me know NOW!!! if you are going to dinner with us. HERE IS THE INFO: *Saturday Night Dinner at 7PM*: SIGNUP FOR DINNER RESERVATIONS HERE <https://docs.google.com/spreadsheets/d/1uPXhGjZlyJJ7xuD7sBoplteTDLXAa34svEz…> * Patrick's Grille : https://patricksgrillenc.com/ ADDRESS: 62 W Sylvania Ave, Neptune City, NJ 07753 Please let me know if you are coming, I'm making reservations tomorrow Friday and need a headcount. ========================================= Jeff Brace VCF National Board Member Chairman & Vice President Vintage Computer Festival East Showrunner Vintage Computer Federation is a 501c3 charity https://vcfed.org/ <http://www.vcfed.org/> jeffrey(a)vcfed.org

1 0

2/11-2/12 Repair Workshop Weekend -- I could use help with some SCSI disk data recovery
by Dan FitzGerald 09 Feb '23

09 Feb '23

Folks, I will be coming to the Repair Workshop both days this weekend, and I am bringing some Macintosh SCSI hard drives that need data recovery. Are any of the folks who are coming able to bring their tools/knowhow for imaging misbehaving SCSI disks? Regards, Dan FitzGerald They/Them/Theirs http://www.vm.ibm.com/devpages/dfitzger

1 0